Buy ASTM D CLASSIFICATION SYSTEM FOR NYLON INJECTION AND EXTRUSION MATERIALS (PA) from SAI Global. ASTM D Standard Classification System for Nylon Injection and Extrusion Materials (PA). standard by ASTM International, 07/01/ View all product. 暂无评价|0人阅读|0次下载 | 举报文档. D – 01A Nylon Injection and Extrusion Materials_能源/化工_工程科技_专业资料。ASTM D标准.

Author: Shajind Gogor
Country: Malta
Language: English (Spanish)
Genre: Automotive
Published (Last): 24 September 2016
Pages: 477
PDF File Size: 5.83 Mb
ePub File Size: 14.48 Mb
ISBN: 766-2-60379-867-3
Downloads: 82651
Price: Free* [*Free Regsitration Required]
Uploader: Bazshura

It is possible, by agreement between the buyer and the seller, that materials incorporating other pigments or soluble stabilizers, or both, may prove adequate for particular applications. D — 96a: It is not intended for the selection of materials. If necessary, additional control of these reinforcements and additives can be accomplished by use of the suffix part of the system see Section 5.

It is possible that materials incorporating other pigments or soluble stabilizers, or both may prove adequate for particular applications. D If a speci? The designation PA indicates the following: Historical Version s – view previous versions of standard.

Industrial & Engineering Plastics

Material selection should be made by those having expertise in the plastic? The test specimen is a disk If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. NOTE 10—When a grade of polyamide is not fully identi?

  C4161 DATASHEET PDF

Users of this standard are expressly advised that determination of wstm validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. F Flexural modulus shall be determined on Test Method D test specimens 3. General Principles ISO Testing Conditions ISO Flexural modulus shall be determined on Test Methods D test specimens 6.

These may be specified by using the suffixes as given in Section 5. NOTE 11—Pigmented or colored nylons can differ signi? D — These shall be agreed upon between the user and the supplier, by using the suffixes as given in Section 5. It is the responsibility d066 the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory axtm prior to use.

These will be spelled out in detail and identi? Tensile strength and elongation shall be determined on Test Method D test specimens 3.

The melting point, Tm, is obtained from the second melting curve. This standard has been approved for use by agencies of the Department of Defense.

Current edition approved August 10, Requirements are based on unannealed test specimens 3. An example of an unreinforced nylon material is given as follows: Material data for inje Relative viscosities of Groups 03 and 04 shall be measured on 0. D40066 specimens tested are 3. Step-by-step testing shall be carried out using?

ASTM D – 94b Standard Classification System for Nylon Injection and Extrusion Materials (PA)

Seven laboratories, including 3 U. Note 1 — There is no known ISO equivalent to this standard. I Groups 03 and 04 materials use Speci?

  AVANUM AVALUM NOVEL PDF

The reinforcement letter designations and associated tolerance levels are shown as follows: The following pieces are to be used for the listed relevant test methods: The designation PAG35 indicates the following: Asttm 4—An example of this classi?

Link to Active This link will always route to the current Active version of the standard. All other grades are listed by requirements.

Viscosities for Groups 03, 04, 06, and 08 are measured as described as follows. D Terminology Relating to Plastics. D ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this wstm.

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. D Practice for Sampling of Plastics. Voltage increments for the step-by-step test shall be determined from short-time test results as follows: Some of these compositions are also suitable for compression molding and application from solution.

Plastic and Ebonite ISO The lot-acceptance inspection shall consist of the tests listed as they apply: